Chassis
- Mercedes-Benz Unimog
- Unimog heavy duty chassis
- Wheel base 3850 mm (12′ 8″)
- U-section frame
- Torsional flexible load carrying frame
- Cross country ratio transmission
- Additional gearbox with crawler gears for hill climbing capacity over 100% grade
- All gears usable both forward and reverse
- Four wheel drive can be selected while driving
- Differential locks for both front and rear axle, can be selected while driving
- Fully protected drive train using torque tube technology
- High mounted gear transmission
- High ramp breakover angle
- Portal axels for high axle ground clearance
- Front and rear tires follow same track
- Enhanced driving safety using coil springs, shock absorbers and stabilizers both front and rear
- Four wheel disk brakes
- Enhanced water fording capacity with raised engine air intake and vent openings
- Torsion free drivers cab mounting using 3 point kinematic mount
- Soundproofed and viabration isolated drivers cab
- Raised drivers cab ceiling for additional equipment space and spare tire storage
- Hydraulic power steering
- Air brakes and power assisted clutch
- Engine compartment easily serviced from exterior hood
- Manual hydraulic drivers cab tilt
- Low emmision turbo diesel engine
- Engine oil lubrication system designed for extreme tilt and slope
- Engine enclosure for lower noise emission
Body
- Mercedes-Benz approved, low 3 point kinematic attachment with main and flex mounts
for stress free body coupling to the torsion elastic chassis frame
Body unit construction - Self supporting UNICAT sandwich plate panels of fibre glass composite (corrosion free)
- Panel connections made by adhesive bond to custom extrusions
eliminates metallic heat conduction paths - Matched thermal coeficients of expansion prevent distortion with changes in temperature
- Wall thickness 60 mm (2.36″) with polyurethane foam insulation, 3 mm (0.12″) FRP outer surface, 2 mm (0.08″) FRP inner surface, insulation rating 0.44 W/m2 K (0.078 Btu/ft2 hr °F)
- Bottom panel at 95 mm (3.7″) thickness, compound construction of plywood bottom,
foam body, integrated welded steel frame and surfaces of FRP
Access to drivers cab - Highly flexible waterproof bellows coupling
Doors and hatches - UNICAT door and storage hatches constructed of fibreglass composite plates and frames
- Thickness of door 60 mm (2.36″)
- Double sealed doors and panels
- Heavy duty locks with seal compression
- Stainless steel hinges throughout
- Additional retractable bolts at top and bottom of doors
- Safety cylinder locks all keyed alike
Windows and skylights - UNICAT burglarproof, scratchproof sidelights and skylights
- UNICAT window frame made of extrusions, coldspot and corrosion free
- Double insulated thermal security window glass
Interior layout
- Seating unit mounted on pedastel
Office place - Desk with integrated PC and printer
- Swivel chair for office place or seating unit
Beds - 2 single beds in the back fitted with comfortable mattresses and duckboards
- Size: 800 x 2060 / 1810 mm (2′ 7″ x 6′ 7″ / 5′ 11″)
Shower and wash room - Shower in entrance way with combined door, to seperate either from toilette or livingroom
- Table with integrated sink
Toilet - Seperated toiletroom
- Also usable as drystorage due to its own radiator
Kitchen - Diesel powered ceramic stove
- Conventional/microwave oven
- Household size stainless steel sink with single handle faucet
- 100 l (22 gallon) fridge
- 40 l (8.8 gallon) deep freezer box
- Kitchen closet with drawers
- Hanger closets with halogenlamps
Storage - Storage space at the office place
- Hanger clothing closet with pull-out hanger bar
- Storage cabinet with drawers under the bed
- Linen cupboard with drawers
- Hanger closets over the beds
- Outside storage cabinets under the two beds
Workmanship - All furniture is built to the highest cabinetmaking standard,
made of wood core plywood using heavy duty locks and hinges - Materials and finishes may be specified by customer
Layout - Design and color of floor, walls, ceiling and upholstery may be chosen by the customer
- Walls and ceiling are painted with multiple coats
Technical equipment
- Custom control panel to control power management and liquide storages
- Battery main switch, savety cutout, fault current breaker
- DC power supply by battery bank, automatic I-U regulated alternator
and AC automatic I-U shore charger with cell temperature sensing - Inverter for 120/240 V
- Power plugs for 12 V, 120/240 V and 400 V
- Pre-wired for solar system
- Pre-wired for TV, video and music system
Generator - Watercooled diesel generator, remote controlled
- Raised exhaust and air intake system
- Water fording capacity due to overpressure system
- AC and rotary current, power 4 kVA
Lighting - Integrated low voltage quartz halogen lights above the table,
office place, kitchen, hall way, shower, toilette and storage area
Water supply - 440 l (97 gallon) freeze-proof drinking water tanks
- 22 l (5 gallon) hot water heat-exchanger
- Stainless steel freeze-proof waste water tank
- Water faucets in both bath and kitchen have removable sprayers
- All components are built due to highest household quality standards
- All plumbing is insulated to prevent freezing
Toilet - Porcelain-vacuum toilet with water flushing
- Stainless steel, freeze-proof sewage holding tank
Heating system - 4 stage diesel/electric-motor lost heat powered warm water central heating (2 x 5 kW),
with engine and diesel preheating system - Waste and sewage holding tank heating
- Radiators in living and bath area
- Antifrost system
General information
- 11,900 kg (26,000 lbs